Categories

LHD Cable vs AT-AS03 Aspirating Smoke Detection for BESS Fire Detection | ANWETECH

Compare ANWETECH LHD cable and AT-AS03 electrical micro-environment detector for BESS fire detection. Learn when to use fixed-temperature heat detection or active air-sampling multi-parameter early warning.
LHD Cable vs AT-AS03 Aspirating Smoke Detection for BESS Fire Detection | ANWETECH
Case Details

Why BESS Fire Detection Needs the Right Detection Method

Battery Energy Storage Systems, also known as BESS, contain battery modules, DC cables, busbars, electrical terminals, control circuits, protection devices and ventilation components. These components are often installed inside battery cabinets, electrical compartments, containerized BESS units or compact equipment spaces.

For this type of application, fire detection should not be selected only by product name. The correct selection depends on what the project needs to detect:

Heat rise near battery modules, cable routes and electrical terminals

Fine particles or characteristic gases released at an early stage

Temperature and humidity changes inside confined electrical spaces

Alarm and fault signals for integration with the fire alarm or monitoring system

ANWETECH provides different detection technologies for different BESS risk stages. The Digital Linear Heat Detector, also called LHD cable or linear heat detection cable, is mainly used for continuous fixed-temperature heat detection along the protected route. The AT-AS03 Electrical Micro-environment Thermal Overload Detector is an active air-sampling early warning device for small electrical confined spaces.

This article compares these two ANWETECH products for BESS fire detection and explains when to select each solution.

Product 1: ANWETECH Digital Linear Heat Detector / LHD Cable

ANWETECH Digital Linear Heat Detector is a linear heat detection system solution. The system is composed of three main parts:

Linear Heat Sensing Cable

Adapter Unit / Interface Module

Termination Unit

The LHD cable is installed along the protected route. It provides continuous heat sensing over the cable path. The adapter unit monitors the cable status and transmits a confirmed alarm signal to the Fire Alarm Control Panel through a 24VDC interface. The termination unit provides end-of-line termination for the sensing loop.

The operating principle is fixed-temperature heat detection. When the sensing cable is exposed to its rated alarm temperature, the NTC polymer matrix between the two conductors changes state and causes a short circuit. This change is monitored by the adapter unit and converted into a fire alarm signal.

For BESS applications, LHD cable is suitable when the project needs direct heat detection close to the possible overheating route.

Typical BESS installation positions may include:

Battery module rows

DC cable routes

Busbar areas

Electrical terminal sections

Power distribution areas

Cabinet side cable paths

Ventilation-adjacent electrical zones

The key advantage of LHD cable is that it follows the hazard path. If the design target is cabinet-level heat detection, the cable can be arranged near the areas where abnormal heat rise may occur.

LHD Cable Technical Points for BESS Projects

ANWETECH LHD cable has several features that are useful for engineering projects:

Continuous linear sensing capability

Fixed-temperature alarm response

Real-time status monitoring

No field calibration or temperature adjustment required

Compatible with 24VDC FACP inputs or passive input modules

Multiple rated alarm temperature options

The available rated alarm temperatures include:

68°C

88°C

105°C

138°C

180°C

For a battery energy storage cabinet, the correct alarm temperature should be selected according to the maximum normal operating temperature inside the cabinet, ventilation condition, distance from the heat source and project fire detection requirement.

The adapter unit model is AT-LHMI. It operates on 24VDC with a 16–28VDC range. It supervises the sensing cable and provides alarm and fault status. The termination unit model is AT-LHME and is a passive non-powered device used at the end of the sensing loop.

This makes LHD cable a practical choice when the project requires a simple, route-based heat detection system connected to a conventional fire alarm panel or input module.

Product 2: AT-AS03 Electrical Micro-environment Thermal Overload Detector

AT-AS03 is not simply a traditional point smoke detector. It is an Electrical Micro-environment Thermal Overload Detector designed for early fire warning in small electrical confined spaces.

According to the ANWETECH AT-AS03 manual, the detector actively analyzes the following parameters from air samples:

Particulate concentration

Characteristic gas concentration

Temperature

Humidity

The AT-AS03 can monitor real-time particulate values, characteristic gas values such as H₂, CO, CH₄ and VOC, as well as real-time temperature and humidity values in the target environment.

This product is suitable for:

Communication equipment cabinets

Power system equipment

Internet data center cabinets

Power distribution cabinets

Compact substations

Other electrical confined spaces

For BESS applications, the AT-AS03 is suitable when the protected object is a small cabinet or confined electrical microenvironment where early warning is required from sampled air parameters.

AT-AS03 Working Principle

The AT-AS03 adopts laser cavity detection technology and gas sensitivity technology. It can detect fine particles and characteristic gases released in the early stages of material combustion.

When materials begin to overheat or burn, the number of particles in the air increases sharply and characteristic gases may be produced. The AT-AS03 actively samples this mixed air into the detection core. It uses the obscuration principle to analyze particulate concentration and gas sensitivity technology to analyze characteristic gas concentration.

When the target air parameters reach the set alarm threshold, the detector generates an alarm and notifies fire safety personnel or the monitoring system.

For BESS cabinet applications, this means AT-AS03 is suitable for monitoring the microenvironment of a cabinet or confined electrical space, especially where the project needs to detect early particulate or gas-related changes before a fixed-temperature heat alarm condition is reached.

AT-AS03 Technical Points for BESS Projects

The AT-AS03 manual provides several engineering details that are important for BESS cabinet applications:

Protected space: 2m³

Particulate sensitivity range: 0.005 to 20% obs/m

Characteristic gas detection: CO 1–1000ppm as default configuration

Temperature detection range: -20°C to +80°C

Operating temperature: -20°C to +55°C

Operating humidity: 5% to 95%, non-condensing

Rated operating voltage: 220Vac

Operating voltage range: 176–290Vac

Maximum power: 2W

Communication method: RS485, 1 channel

Relay output: 1 pair

Relay load capacity: AC 60V 1A / DC 60V 1A

Event records: 30,000 entries

Alarm levels: 5 levels, adjustable

Display and operation: indicator lights / smart terminal

Installation method: wall-mounted / 35mm rail installation

These parameters show that AT-AS03 is designed for small electrical spaces and cabinet-level microenvironment monitoring. It is not a long-route heat sensing cable. It is an active sampling detector that evaluates multiple air parameters and provides early fire warning based on a data model and alarm thresholds.

Core Difference: LHD Cable Detects Heat, AT-AS03 Analyzes Air Samples

The main difference between the two products is not only “heat vs smoke.” A more accurate engineering comparison is:

LHD Cable detects fixed-temperature heat along a linear cable route.

AT-AS03 actively samples air and analyzes particulate concentration, characteristic gas concentration, temperature and humidity inside a small electrical microenvironment.

This difference is very important for BESS fire detection.

If the project needs direct thermal detection near a battery module row, DC cable route, busbar or cabinet wiring path, LHD cable is more suitable.

If the project needs early warning inside a small cabinet space by analyzing air samples for particles, characteristic gases, temperature and humidity, AT-AS03 is more suitable.

They solve different problems and can also work together in a layered BESS fire detection strategy.

Comparison Table: LHD Cable vs AT-AS03 for BESS Fire Detection

Comparison Item ANWETECH LHD Cable ANWETECH AT-AS03
Product Type Digital Linear Heat Detector Electrical Micro-environment Thermal Overload Detector
Detection Target Fixed-temperature heat along the cable route Particulate concentration, characteristic gases, temperature and humidity in air samples
Detection Principle NTC polymer matrix changes state at rated temperature Laser cavity detection + gas sensitivity technology
Best Application Heat detection near battery modules, cable routes, busbars and electrical sections Early warning in cabinet microenvironment and electrical confined spaces
Coverage Method Continuous linear route coverage Active air sampling in protected small space
Protected Area Logic Along the installed cable path Up to 2m³ protected space
System Components Sensing cable + adapter unit + termination unit Detector AT-AS03 + background monitoring software
Output / Communication Adapter unit transmits alarm to FACP through 24VDC interface RS485 communication and 1 pair ALM relay output
Alarm Type Fixed-temperature heat alarm Multi-parameter threshold alarm
Temperature Data Rated alarm temperature options: 68°C / 88°C / 105°C / 138°C / 180°C Temperature detection range: -20°C to +80°C
Suitable BESS Use Cabinet internal cable routes, battery rows, busbars, electrical terminals BESS cabinet, power distribution cabinet, compact electrical confined space
Engineering Role Direct heat detection layer Early microenvironment warning layer

When to Choose LHD Cable for BESS

Choose ANWETECH LHD cable when the BESS project requires direct heat detection along a defined route.

This is especially suitable when the risk area is long, narrow or route-based. In a BESS cabinet, heat risk may develop along cable channels, battery module rows, busbars or terminal connections. LHD cable can be arranged near these areas to provide continuous fixed-temperature detection.

LHD cable is recommended when:

The project needs direct heat detection near critical points

The protected path follows battery modules or cable routes

The cabinet layout allows cable installation along the risk route

A fixed-temperature heat alarm is required

The system needs to connect to a conventional fire alarm panel or input module

The project needs continuous linear heat detection rather than one-point detection

The route is hard to access after cabinet installation

For BESS applications, LHD cable should be selected according to the normal cabinet temperature and the required alarm temperature rating.

When to Choose AT-AS03 for BESS

Choose AT-AS03 when the project requires early fire warning from a small electrical confined space or cabinet microenvironment.

The AT-AS03 is suitable for cabinet applications because it actively samples air and analyzes multiple parameters. It is designed for spaces such as power distribution cabinets, communication equipment cabinets, IDC cabinets and compact substations. These application types are similar to the confined electrical spaces found in many BESS cabinet projects.

AT-AS03 is recommended when:

The protected space is a small cabinet or electrical enclosure

The project needs early warning based on particles and characteristic gases

Temperature and humidity monitoring are also useful for the application

The design requires RS485 communication to a monitoring computer

The project needs alarm/fault output through relay contacts

The cabinet space is approximately within the detector’s protected space range

A multi-level alarm strategy is required

Historical alarm records and event logging are useful for maintenance

For BESS cabinet applications, AT-AS03 provides a microenvironment detection layer that is different from simple fixed-temperature heat detection.

Can LHD Cable and AT-AS03 Be Used Together?

Yes. For BESS fire detection, LHD cable and AT-AS03 can be used together because they detect different risk signals.

LHD cable is installed near battery modules, cable routes or electrical sections to detect fixed-temperature heat rise along the protected route.

AT-AS03 monitors the cabinet or confined electrical microenvironment by actively sampling air and analyzing particulate concentration, characteristic gases, temperature and humidity.

This layered approach can provide more complete detection logic:

LHD cable provides direct heat detection.

AT-AS03 provides early microenvironment warning.

The fire alarm or monitoring system can receive signals from both technologies.

The project engineer can define alarm response logic according to site requirements.

For example, in a BESS cabinet, AT-AS03 may be used to monitor the cabinet air environment, while LHD cable may be installed along battery rows or cable paths. This combination helps cover both early air-sample changes and direct heat rise near critical components.

BESS Application Design Logic

For a BESS project, product selection should start from the risk location.

If the risk is a cable route, busbar, terminal or battery module row, LHD cable can provide direct fixed-temperature heat detection along that route.

If the risk is a confined cabinet microenvironment where early particles or characteristic gases may appear, AT-AS03 can actively sample and analyze the air.

If the project requires both direct heat detection and early warning, both products can be combined.

The design should consider:

Cabinet internal space

Battery module arrangement

Cable routing

Ventilation airflow

Normal operating temperature

Electrical compartment layout

Alarm signal integration

Monitoring system requirement

Maintenance accessibility

Required fire safety response logic

This approach helps avoid choosing a product only by name. Instead, the detection technology is matched to the actual BESS fire risk.

Fire Alarm and Monitoring Integration

The two products have different integration methods.

For LHD cable, the sensing cable is connected to the AT-LHMI adapter unit. The adapter unit supervises the cable and transmits alarm and fault signals to the Fire Alarm Control Panel through a 24VDC interface. The AT-LHME termination unit completes the sensing loop.

For AT-AS03, the detector provides RS485 communication and one pair of ALM relay output. It can communicate with the background monitoring computer and upload data for users to view and take action. The device also supports indicator lights, smart terminal operation, multi-level alarm function and historical alarm record storage.

In a BESS project, this means:

LHD cable is suitable for fire alarm panel input and route-based heat alarm.

AT-AS03 is suitable for cabinet microenvironment monitoring, RS485 communication and alarm relay output.

Both products can be integrated according to the project fire alarm and monitoring system design.

Maintenance and Operation Considerations

LHD cable is a fixed-temperature heat detection cable. It does not require field calibration or temperature adjustment. During design and installation, the correct alarm temperature and cable route should be selected.

AT-AS03 requires regular maintenance of the filter cartridge. According to the manual, the filter cartridge is the component that requires regular replacement, with a service life of about one year. The service life may be shorter in dusty environments. The detector maintenance plan includes monthly, quarterly, semi-annual, annual and biennial maintenance recommendations.

For BESS cabinet projects, this means:

LHD cable focuses on correct routing and rated temperature selection.

AT-AS03 focuses on air inlet condition, filter maintenance, parameter setting and communication check.

A proper maintenance plan is important for both detection reliability and long-term project operation.

Recommended Selection Strategy

For Battery Energy Storage Cabinets:

Use LHD cable when the main design target is direct heat detection along battery module rows, cable routes, busbars or electrical terminals.

Use AT-AS03 when the main design target is early warning by sampling cabinet air and analyzing particles, characteristic gases, temperature and humidity.

Use both when the project requires layered detection for both heat rise and early microenvironment changes.

For BESS Rooms or Containerized Systems:

Use LHD cable for cabinet internal route-based heat detection.

Use AT-AS03 for compact electrical confined spaces where one detector can cover the protected microenvironment.

Use other room-level or container-level fire detection solutions if the protected space is larger than the AT-AS03 protected range or requires a different detection design.

Benefits of ANWETECH BESS Detection Solution

ANWETECH can provide different detection technologies for different BESS fire risk points.

LHD cable provides:

Continuous linear heat detection

Fixed-temperature alarm response

Direct installation near risk routes

Multiple alarm temperature options

FACP connection through adapter unit

AT-AS03 provides:

Active air sampling

Particulate and characteristic gas detection

Temperature and humidity monitoring

Multi-parameter visualization

Multi-level alarm function

RS485 communication

Relay alarm output

Historical alarm and event records

Together, these two technologies can support a more complete BESS cabinet fire detection strategy.

Common Misunderstandings

Misunderstanding 1: LHD Cable and AT-AS03 Detect the Same Thing

They do not. LHD cable detects fixed-temperature heat along a route. AT-AS03 actively samples air and analyzes particulate concentration, characteristic gas concentration, temperature and humidity.

Misunderstanding 2: AT-AS03 Is Only a Smoke Detector

AT-AS03 should not be described only as a smoke detector. It is an electrical microenvironment detector that uses laser cavity detection and gas sensitivity technology for multi-parameter early warning.

Misunderstanding 3: LHD Cable Can Replace Microenvironment Detection

LHD cable is suitable for heat detection, but it does not analyze air samples, gases, particulate concentration, humidity or microenvironment data.

Misunderstanding 4: One Product Fits Every BESS Area

A battery cabinet, power distribution cabinet, BESS room and containerized energy storage system may require different detection layouts. Product selection must match the protected space and fire risk.