Categories

Aspirating Smoke Detection for Underfloor Voids and Concealed Cable Spaces | ANWETECH AS01

ANWETECH AS01 provides aspirating smoke detection for underfloor voids, raised floors, concealed cable spaces, electrical rooms, UPS rooms, server rooms, battery rooms, and other critical facilities requiring very early fire warning.
Aspirating Smoke Detection for Underfloor Voids and Concealed Cable Spaces | ANWETECH AS01
Case Details

Aspirating Smoke Detection for Underfloor Voids and Concealed Cable Spaces

Introduction

Underfloor voids and concealed cable spaces are often hidden from normal visual inspection, but they may contain some of the most important fire risk points in a building. Power cables, communication cables, control wiring, UPS connections, distribution circuits, and cable trays may all pass through these spaces. Once overheating, insulation damage, loose connections, or cable faults occur, smoke can develop inside the concealed area before it reaches the occupied room.

In many projects, conventional ceiling-mounted smoke detectors may not detect this early smoke quickly enough. Smoke generated below a raised floor or inside a cable void may remain trapped, move along cable routes, or be diluted by airflow before reaching the ceiling.

ANWETECH AS01 Stand-Alone Laser Cavity Aspirating Smoke Detector is designed for very early warning smoke detection. It actively draws air samples through a pipe network, analyzes smoke particle concentration inside a laser cavity, and provides alarm outputs when smoke levels reach preset thresholds. This makes it suitable for underfloor voids, raised floors, concealed cable spaces, electrical rooms, server rooms, UPS rooms, battery rooms, cable tunnels, laboratories, museums, archives, and other critical facilities.

Why Underfloor Voids and Concealed Cable Spaces Are Fire Risk Areas

Underfloor and concealed spaces are widely used in modern buildings and technical facilities. They are often used to route electrical cables, data cables, control wiring, air distribution, and equipment connections. Although these spaces are normally hidden, they can carry a high concentration of electrical loads.

Common fire risks include:

Overheated power cables
Damaged cable insulation
Loose electrical terminals
Aging wiring inside cable trays
UPS or battery-related abnormal heating
Dust accumulation around cables and supports
Poor ventilation inside concealed voids
Smoke trapped below raised floors or inside hidden spaces

The challenge is that early smoke may not be visible from the room. By the time smoke reaches a ceiling detector, the fault may already have developed further. For this reason, these areas require an early smoke detection method that can monitor the hidden space directly.

Limitations of Conventional Smoke Detection in Hidden Spaces

Point-type smoke detectors are usually installed on the ceiling or in open areas. They are effective for many standard rooms, but underfloor voids and concealed cable spaces create special detection challenges.

Smoke may remain below the raised floor.
Cable trays may guide smoke horizontally instead of upward.
Airflow may dilute or redirect smoke.
Hidden spaces may be difficult to access for inspection.
Ceiling detectors may respond only after smoke escapes from the void.
Small early-stage smoke particles may not be detected quickly enough by conventional room-level detection.

For critical facilities, waiting for smoke to leave the concealed space can reduce response time. A better approach is to sample the air directly from the risk area.

How Aspirating Smoke Detection Works in Underfloor Voids

Aspirating smoke detection uses a sampling pipe network to actively draw air from the protected space into the detector. Instead of waiting for smoke to naturally move to a fixed detector location, the system continuously collects air samples from multiple sampling holes.

For underfloor voids and concealed cable spaces, sampling pipes can be arranged along cable trays, raised floor areas, electrical voids, cabinet rows, or hidden equipment spaces. Air is drawn from these sampling points and transported to the AS01 detector.

Inside the detector, a laser cavity analyzes the smoke particle concentration. When the smoke concentration exceeds the preset threshold, the detector triggers the corresponding alarm level and provides output signals through relay contacts or RS485 communication.

This active air sampling method helps detect smoke directly from the hidden area before it spreads into the main room.

ANWETECH AS01 for Concealed Cable Space Protection

ANWETECH AS01 is a stand-alone laser cavity aspirating smoke detector designed for very early warning smoke detection. It combines active air sampling, laser-based smoke particle analysis, multiple alarm levels, real-time display, RS485 communication, and relay outputs.

For underfloor void and concealed cable applications, AS01 can help engineers build a practical early warning system for hidden fire risks.

Key advantages include:

Active air sampling from hidden areas
Laser cavity smoke particle detection
Multiple alarm levels for staged response
RS485 communication for monitoring system integration
Relay outputs for connection with fire alarm panels or BMS systems
Real-time smoke concentration display
Sampling pipe network for flexible installation
Suitable for concealed spaces and equipment areas

Typical Application Areas

AS01 is suitable for more than data centers. It can be used in many facilities where hidden spaces and cable routes require early smoke detection.

1. Raised Floor Areas

Raised floors are commonly used in technical rooms, control rooms, computer rooms, communication rooms, and commercial buildings. They may contain power cables, signal cables, control wiring, and air distribution paths. Aspirating smoke detection allows the air below the floor to be monitored directly.

2. Underfloor Cable Voids

Underfloor cable voids can hide early smoke from cable overheating or insulation failure. Sampling pipes can be installed along cable routes to continuously monitor the concealed space.

3. Electrical Rooms

Electrical rooms and power distribution rooms often contain cable trays, panels, switchgear, and control wiring. Early detection is important because electrical faults can develop quickly. AS01 can provide early warning before smoke spreads into the room.

4. Server Rooms and Data Centers

Server rooms and data centers often use raised floors, cable trays, UPS equipment, and power distribution systems. Aspirating smoke detection can monitor both open room areas and hidden underfloor spaces.

5. UPS Rooms and Battery Rooms

UPS rooms and battery rooms may contain high electrical loads and concealed cable connections. Early smoke detection helps operators investigate abnormal heating or smoke generation before a fire escalates.

6. Communication Rooms and Control Rooms

Telecom rooms, control rooms, and monitoring rooms contain dense wiring and sensitive electronics. AS01 can support early warning detection in concealed cable routes and technical floor voids.

7. Cable Tunnels and Cable Trenches

Cable tunnels and cable trenches are high-risk areas because large numbers of cables are installed in confined spaces. Aspirating smoke detection can be considered where early smoke detection and remote monitoring are required.

8. Clean Rooms, Laboratories, Museums, and Archives

Some facilities require very early fire detection to protect sensitive equipment, samples, documents, cultural assets, or valuable materials. Concealed cable spaces in these environments should not be ignored.

Engineering Design Considerations

A successful aspirating smoke detection design depends not only on the detector, but also on the sampling pipe layout.

Engineers should consider:

Location of cable trays and cable bundles
Raised floor height and void structure
Airflow direction below the floor
Sampling hole spacing and orientation
Pipe route and total pipe length
Protection of sampling pipes against damage
Accessibility for inspection and maintenance
Dust level inside the concealed space
Integration with fire alarm panel, BMS, or monitoring system
Local fire safety code requirements

For underfloor void applications, sampling holes should be arranged to capture air from the most likely smoke generation areas. Pipe connections should be sealed properly to prevent air leakage, and the system should be tested after installation to verify airflow and smoke response.

Technical Highlights of AS01

ANWETECH AS01 provides important technical features for concealed space protection:

Power supply: 24V DC
Power consumption: less than 30W
Sensitivity range: 0.001–28% obs/m
Detection area: up to 1,000 m² per detector
Pipe length: up to 2 × 100 meters
Sampling holes: 26 per pipe, 52 total
Communication: RS485 interface
Alarm records: 32,000 events
Dimensions: 300 × 230 × 98 mm
Weight: less than 3 kg
Operating temperature: -40°C to +65°C
Humidity range: 0–100% RH, non-condensing

These parameters allow AS01 to be used in various engineering environments where flexible pipe sampling and centralized monitoring are required.

Alarm and System Integration

AS01 provides multiple alarm levels and signal outputs. The detector can be connected to fire alarm systems, building management systems, or monitoring software according to project requirements.

Typical integration methods include:

RS485 communication for monitoring
Relay outputs for alarm signal transmission
Fault output for system supervision
Reset input for system control
Connection to fire alarm control panels
Connection to BMS or remote monitoring systems

For gas suppression or clean agent systems, AS01 should normally be used as an early warning detection and signal source. The actual release logic should be handled by a dedicated releasing control panel with delay, manual release, abort function, alarm confirmation, and local code-compliant safety sequence.

Maintenance for Reliable Detection

Underfloor voids and concealed cable spaces may accumulate dust over time. Regular maintenance is important to keep the sampling system reliable.

Recommended maintenance includes:

Monthly airflow check
Quarterly smoke test
Semi-annual visual inspection of sampling pipes
Annual full system inspection and testing
Filter replacement according to system condition
Pipe cleaning when dust or blockage is found
Verification of airflow after cleaning
Checking all sampling holes for blockage

Proper maintenance helps ensure that the detector continues to receive accurate air samples from the protected area.

Why Choose ANWETECH AS01

ANWETECH AS01 is suitable for underfloor voids and concealed cable spaces because it detects smoke from the hidden area itself, rather than waiting for smoke to reach the room ceiling. Its active air sampling design allows engineers to monitor hard-to-reach spaces, cable voids, raised floor areas, and equipment rooms with a flexible sampling pipe network.

For critical facilities, the value of AS01 is early response. The earlier smoke is detected, the more time the operator has to inspect, isolate equipment, shut down affected circuits, and prevent a small electrical fault from developing into a serious fire event.